EV FAQs and Figures

Note: This article is about fully electric vehicles. Not hybrids.

Illustration of an EV being chargedPhoto iStock, Credit: Golden Sikorka

Electric Vehicle Costs

Sales

How Much Do EVs Cost to Buy?  

Electrical vehicles can run from $30,000 on the low end to over $100,000 on the high end, with Tesla being the major seller with 1,917,450 vehicles sold since it was first introduced.

Elon Musk who owns Tesla brought in a revenue of $53.8 billion for the year 2021. Aside from Tesla, other manufacturers jumped on the bandwagon to make electric vehicles such as BMW, Nissan, Chevrolet, Ford, Volkswagen, and Kia.

2023 Update: Most EV buyers are heading to Tesler over other manufacturers. According to one dealership, they had to lower the price of their EVs because “They are not selling”.

Charging

How Much Does It Cost to Charge an EV from Your House? 

White Tesla Model 3 Charging at Home
Austin, Texas, USA – 2-1-2021: Tesla Model 3 charging at home in front of the house on the L2 at-home charging that is provided with every Tesla vehicle

According to our calculations, it can cost between $10 – $15 per charge to the recommended 80% when your EV is near zero battery capacity, which equates to 230 miles. That is less than 1/2 the cost of what a conventional gas car would cost to drive the same distance. If your battery has more than zero juice, your electrical cost would be even less to reach the 80% – 230-mile range.

How Much Does It Cost to Charge an EV Outside of Your House?

Electric Vehicle being charged in a garage
Photo by Michael Fousert on Unsplash

The cost to charge your EV depends upon several factors, but in general, expect to pay between $20 – $30 for a full charge, which is much better than a conventional gas car expense, since you can add a good 200 – 300 miles back to the battery. Try getting 200 miles for $30 on a conventional car!

Electrical Charging an EV

What is the Difference Between Level 1 and Level 2 Chargers?

There are some major differences. A level 1 charger can be plugged into any 110-volt outlet, but charges at about twice as long as a level 2 charger, which connects to a 220/240-volt outlet. If you recall our article on voltage, it is the amount of current that is ‘pushed’ out. Like a water faucet. The more you move the lever, the faster the water comes out. So a level 1 charger that uses 110 volts, the amount of current is, on average 15 amps. A level 2 charger can draw up to 60 amps, depending on the size of the breaker in the house.

Why are There Two Batteries in My EV?

Power Battery: The main battery is the EV battery, technically called the traction battery because it is the battery that provides the power to drive the car.

Auxiliary Battery: This battery is the standard ‘starter12-volt battery’ that we see in all cars (conventional gas and EVs).  The battery is responsible for powering auxiliary systems such as lights, radios, climate control, and all other electronics in the vehicle. Most importantly, it is the battery that is used for starting the car.

If you are in an EV and you press the Start button but nothing happens or weird things occur like flasing internal lights but the cat won’t start, it will be the auxiliary battery that is causing the problem. Not the EV battery.

How is Electricity Sent to the Car’s Devices?

The EV uses a DC-DC converter that converts the higher voltage of the EV battery, called the battery pack to the standard 12 volts needed to power the car’s internal electrical systems.

The actual term for the DC-DC converter is called a step-down converter, as it takes in the higher voltage from the EV and steps down the voltage to 12 volts.

How is the 12-Volt Battery Charged in an EV?

Electric vehicles do not have alternators, which are used to charge the 12-volt batteries in gasoline cars. For EVs, the process is the following:

  1. When the car is running, the DC-DC converter draws power from the high-voltage battery (the battery that drives the car) and converts it to 12 volts. This power is then used to keep the 12-volt battery charged.
  2. When the car is plugged into a charger (home or mobile), the charger takes over to power the DC-DC converter, which then charges the 12-volt battery.

How Long Does It Take to Charge an EV?

Illustration of EV going to get charged
Image by Mohamed Hassan from Pixabay

That depends upon the charger you are using. Currently, there are two types available. A Level-1 charger that connects to any 110-volt outlet. This can take over six hours to fully charge an EV’s battery.

Then there is a Level-2 charger. Charging of this type usually takes about three to four hours to reach full charge.

Shortly, Level-3, called high-speed chargers, will cut this charging time in half or more.

Does Fully Charging Mean It Charges Up to 100%?

No, all EV battery manufacturers agree that these batteries should not be charged to 100% because it will cause degradation of the battery in the long run. Charging to 80% is the recommended charging level and is usually set as the default for most EVs.

You can override this setting if you are planning a long trip but it is not recommended to keep it at the 100% charge level continuously.

So when we say we are fully charging our EV, it means that we have charged up to the 80% mark.

What if My Battery Goes to Zero Miles Left and I Am Sill on the Road?

EV dashboard showing zero mileage let
Zero mileage does not necessarily mean your EV will stop in its tracks, but you should seek an EV station ASAP! Photo SS.

That’s why we recommend not to let your EV battery go below 30%, like the scenario we mentioned above, but we do understand that there are circumstances when this can happen. Chances are you will still have some power left to drive another few more miles. The mileage algorithms are not perfect and only give you an estimate of how much charge you have, but these estimates are fairly accurate as far as estimates are concerned,

When you see that warning notice on your dashboard, you should immediately shut down all accessories (radio, air conditioner or heater, phone charging, etc.) so that the least amount of power is being drained from the battery, but you should look for a charging station immediately!

The Weather and the Seasons

Do the Seasons Have an Effect on EV Batteries?

Car driving in winter snow
Image by Pexels from Pixabay

Yes, especially in winter. If the temperature goes below 40 F degrees, expect the mileage to diminish faster. Case in point: It was late November. A couple was leaving Manhattan to go to Long Island. Their GPS said it was a 27-mile drive and 45 miles were left on the vehicle, but halfway through their drive, the mileage counter dropped to 10 miles. Fortunately, they found an EV station along the way and were able to charge the car.

This is why we always suggest not letting your EV battery get that low. Once you see it is below 30%, you should charge it.

Can I Charge My EV in the Rain?

Lectron 240V 40 Amp Level 2 Electric Vehicle (EV) Charger on ground in the rain
This Lectron 240V 40 Amp Level 2 (EV) Charger has a rubber cap that protects water from getting into the charging port. Photo: SS

If the charger has protection such as non-conductive shielding at the port section, then you should be ok if the charger is left outside in the rain.

Check with your charging manufacturer to determine if your home charger is rainproof, but as with all electrical devices, it is always safer to keep these chargers away from anything wet.

Travel and Long Trips

How Many Miles Can I Get on a Full Charge?

Most EVs in the medium-cost range get about 230 miles on an 80% charge. The manufacturers do not recommend charging to 100% as it decreases the integrity of the battery.

Some of the higher ones, such as the Tesla Model S can get up to 394 miles when the batter is at full capacity. On the other hand, a Kia Niro, a great EV with excellent reviews will get about 253 miles on a full charge. And the 2023 Chevy Silverado will have a 200 kWh battery that can take you a good 400 miles before recharging.

Can I Go on Long Rides With My EV?

Car driving on lonely road
Image by Автошкола ТЕХНИКА from Pixabay

You can but it is not advisable at this time; however, if you are bent on taking long drives with your EV, it is highly recommended that you plan your trip with charging along the way as your main priority. Check the highway’s rest areas to see if they have charging stations, but be aware that if you do have to charge your EV during your trip, you may have to stay a while, possibly a good three to four hours at each station.

As President Biden’s infrastructure bill goes into effect, you will see more and more charging stations appear, especially along the highways, but remember, charging an EV is not like pumping gas into a car. You will be there for a few hours each time you charge your vehicle.

Of course, you don’t have to fully charge your car. If you could just add another 100-150 miles, that would cut down the time spent waiting. 

Either way, plan so that you can find places to go while the car is charging. Some of these locations may have a restaurant where you can have a long dinner or some towns may have charging ports on the street or in garages, or shopping mall parking lots. As you wait you can traverse through the many stores to kill time.

Then there are the hotels. Call ahead to find out if they have EV portals and if not, where is the closest one?

Shortly, more and more charging stations will be added along the highways and private locations such as housing and hotels. Additionally, in Biden’s Build Back Better plan, he has allocated $5 billion to increase the US infrastructure with over 500,000 new EV portals, and that doesn’t include the additions by private enterprises.

Tell Me More About the Mileage Estimates

A rideshare driver was on his way home from his last drop-off in Manhattan. He previously didn’t realize that the drive for this customer was further out than he thought and he saw that he had only 35 miles left on his battery.

Since he lived just outside the city limits in Long Island, he was sure that he would be able to get home before the battery capacity runs out. He was wrong. And this was during the warmer weather.

When the driver was on the highway, only 13 miles from his home, a warning light came on and said he had zero miles left to drive. What was saying 13 miles all of a sudden went to zero, meaning he had no more battery life in his car.

What happened to that missing 13 miles can only be explained by the fact that the mileage algorithms keep refreshing and new estimates materialize. So it is strongly advised to monitor your mileage with a give or take of 10- 15 miles either way. Thinking this way may help you decide when you should make your next charge.

This is especially true for winter driving as we have stated.

EV battery warning light advising low battery
If a warning like this comes on, shut off all unnecessary power and look for an EV station immediately! Photo SS.

Plan Ahead!

If you are going to purchase an EV, plan out your expenses first against what it would cost for a gas car. Then plan out what you plan to do with the car. Will you be using it for local driving or going to work every day or is your main purpose going on long trips? At this current time, we would recommend that you purchase your EV for local driving or work. Whatever you choose, enjoy your ride!

What are the Advantages of Owning an Electric Car?

Of course, the main reason for owning an EV is the savings you get by not having to gas up your car, especially at the prices today. Additionally, EVs don’t have a combustion engine, so there are fewer parts to become defective during your ownership. EVs are said to help with the environment as well and they run very quietly.

What are the Disadvantages of Owning an Electric Car?

The initial expense of purchasing one is what keeps many who would otherwise buy one. Then there is the cost of having a 220-240 volt connection installed into your home circuit box, which can run from $600 to $1000. 

If you live in an apartment, you may run into an additional issue if the building or development you are in does not have an EV portal available, but more and more locations and communities are having EV stations installed such as shopping malls, public garages, and of course, many car dealerships.

Do EVs Need Oil Changes?

No. There are no combustion gas engines in electric vehicles, but cars with gas engines need maintenance. The oil used to keep the pistons running smoothly in the chamber of the engine needs to be changed every six months or 3,000 miles. Since no gas engine runs the car, no oil change is needed.

 

What Components Make Up EV Batteries?

Photo iStock, Credit: Golden Sikorka

E‍V Battery Overview

In our previous article, we discussed the advantages of owning an electric vehicle. Now, let’s delve further into the component of an EV – its battery.

Electric vehicle batteries consist of several subcomponents that work together to store and discharge electricity. These individual sections are also known as cell components or cell materials. The parts combine to form the complete battery and each has its unique properties and function.

When considering the various types of electric car batteries, it’s important. Knowing how they function can help you make a more informed decision when purchasing a new electric car, hybrid, or extended-range electric vehicle (EREV) battery.

What are the Components of EV Batteries?

Before we review these components, we need to make sure we understand what an electrode is.

An electrode is a conductor which is a negatively charged (anode) or a positively charged (cathode) material. You can read more about electrodes here.

The different elements of an electric car battery include the following:

    • Anode – The anode is the negative electrode of the battery. It’s made from a metallic oxide material, such as nickel oxide or iron oxide. Anodes are highly porous, allowing for the movement of electrons.
    • Cathode – The cathode is the positive electrode of the battery. It’s made from graphite, a porous material with high electrical conductivity.
    • Separator – The separator is a thin, porous material that sits between the anode and the cathode. Its purpose is to keep the electrodes from touching each other. This is important to prevent overheating, which could result in the battery catching fire.
    • Electrolyte – The electrolyte is a liquid that serves as a conductor of an electric charge. The electrolyte helps move electrons from the anode to the cathode.
    • Container – The container or housing holds all of the components of the battery in place. It’s made from a corrosion-resistant material, such as stainless steel.
    • Cooling System – The cooling system ensures that the battery does not overheat. This can happen if the battery is overcharged and the temperature of the battery rises.

Battery Cells

Illustration of a battery cell
Photo: Wikimedia CC

The most important component of the battery is the cell, which is often made from lithium-ion or lead-acid materials. The cell is composed of active materials, electrolytes, and electrodes that are used to store and discharge electricity. The electrode is a conductor that helps to move electrons from one electrode to the other.

The most common electrodes used to make the anode and cathode are lithium and lead. Batteries can be composed of one cell or many cells connected  Single-cell batteries are the most common type of electric car battery. Multicell batteries are used in larger-scale storage, such as solar systems or large-scale energy storage systems.

Electronic Parts

The electronic parts of an EV battery include the battery management system (BMS), the charge controller, and the voltage regulator. The BMS is a b16-Monthn electric circuit that’s used to monitor the health of the battery by measuring voltage levels, charging/discharging rates, and temperature.

The BMS can also help to prevent overcharging and over-discharging of the battery. The charge controller is used to charge the battery. It helps to balance the amount of energy used to charge the battery and the amount of energy generated from the grid or solar panel.

The charge controller also measures the amount of current flowing into and out of the battery during charging. The voltage regulator is used to balance the voltage levels of the battery during charging and discharging.

Lead-Acid Batteries

Lead-acid batteries are the oldest type of battery used in electric cars. They are very cheap to produce and are easy to maintain. However, they are not as efficient as other battery types. They also contain toxic materials, such as sulfuric acid.

These types of batteries are typically used in large-scale grid energy storage systems, such as in a commercial or industrial setting. Lead-acid batteries come in both flooded and sealed types, with the flooded type being the most common. Flooded lead-acid batteries are filled with a liquid electrolyte. They are commonly used in electric vehicle systems.

Lithium-Ion Batteries

Lithium is very popular because of the ease with which it can release its electron, which makes it ideal for the electrons to flow between the anode and cathode.

Lithium-ion batteries are very efficient, have a long lifespan, and are capable of being fully charged in less than one hour. They are less expensive than nickel-metal hydride batteries and are used in a wide range of consumer electronics. Currently, hybrid electric vehicles, plug-in hybrid electric vehicles, and electric vehicles used lithium-ion batteries.

Where Do the Materials that Make Up a lithium-ion Battery Come From?

Generally speaking, five minerals are considered essential for Li-ion batteries:

The locations where these materials are mined can originate in many different parts of the world, with China being the major exporter of graphite, which is the most important mineral that comprises the anode for these batteries

Nickel-Metal Hydride Batteries

Nickel-metal hydride batteries are also used in electric cars in both hybrid vehicles and electric vehicles. They are cheaper than lithium-ion batteries and are easier to recycle. 

Conclusion

There are many different types of electric car batteries, each with its unique properties and functions. When considering the various types of batteries, it’s important to understand what makes up these different battery types.

Understanding how they function can help you make a more informed decision when purchasing a new electric car battery or an extended-range electric vehicle battery.

When looking for new batteries, make sure to understand their warranties and how they are manufactured to ensure you get the best product possible. 

Quantum Computing in Simple Terms!

Illustration of quantum light rays
Quantum computing. Close-up of optical CPU process light signal.  Photo: iStock

Quantum Introduction

The term ‘Quantum Computing’ hasn’t gotten the much-needed traction in the tech world as yet and those that have traversed through this subject might find it a bit confusing, to say the least.

Some experts believe that this is not just the future, but the future of humanity. Quantum theory moves ahead of the binary computer and ventures into the world of computing that resides at the subatomic level.

If you don’t have a clue what we are talking about, you are not alone. Stay with us through this article where we will discuss quantum computing in great detail—what it is—how it will change the tech world and its practical implications (both for better or worse).

Before we usher in the discussion of this potential life-changing advancement, it is necessary to discuss the platform on which quantum computing is based – Quantum theory. 

What is Quantum?

Illustration of the Atom
Particles of the atom: protons, electrons, and neutrons. Nucleus. Photo: iStock

Also known as quanta, in simple terms, it represents the minimum amount of energy that can be used within any physical interaction.

Using examples of particle interaction within the atom, a quantum of light would be a photon, and a quantum of electricity would be an electron. There can be no activity smaller than when these particles have an interaction.

In the Beginning

The industrial revolution of the 20th century was one of the greatest milestones of modern history. From the invention of the automobile to industrial steel, elevators, and aircraft, it gave birth to a plethora of things that now define our civilization and will continue to shape the history of our future. 

Enter the 21st century and we are watching a transition from the tangible to the intangible (virtual) world; notably, computer technology, its hardware, software, and the world wide web.

Among the many incredible things that are ensuing during this technological revolution is the colossal development in physics, specifically quantum theory. We will try to keep the explanation of quantum theory as simple as possible to make this as interesting and informative as possible. 

Modern Physics

The field of physics is divided into two definite branches: classical and modern. The former branch was established during the period of the Renaissance and continued to progress after that.

Classical physics is based on the ideas by Galileo and Newton. Their concepts are focused on the macroscopic (visible to the naked eye) of the world around us.

Conversely, modern physics is about analyzing matter and energy at microscopic levels. 

While we are at it, it is important to clarify that quantum theory doesn’t just refer to one idea or hypothesis. It is a set of several principles. We will discuss them simply and remain focused on the items that are relevant to quantum computing. 

    • The work of physicists Max Plank and Albert Einstein in the 20th century theorized that energy can exist in discrete units called ‘quanta’. This hypothesis contradicts the principle of classical physics which states that energy can only exist in a continuous wave spectrum.
    • In the following years, Louis de Broglie extended the theory by suggesting that at microscopic (atomic and subatomic) levels, there is not much difference between matter particles and energy and both of them can act as either particles or waves as per the given condition. 
    • Lastly, Heisenberg proposed the theory of uncertainty, which entails that the complementary values of a subatomic particle can’t be simultaneously measured to give accurate values. 

Neil Bohr’s Interpretation of Quantum Theory: The Primal Basis of Quantum Computing

Illustration of a quantum computer
Image by Pete Linforth from Pixabay

During the period when quantum theory was extensively discussed among top physicists, Neil Bohr came up with an important interpretation of this theory.

He suggested that light cannot be determined if it is composed of particles or waves, called wave-particle duality until they are particularly found out.

The infamous Schrodinger’s Cat experiment is an easy way to understand this concept. The experiment entails that a cat enclosed in a box with poison could be considered both dead and alive until the box is opened and the cat is observed.

Computer Algorithms 

Now, this is the point where the theory demonstrates its potential, but first, a definition of an algorithm – a set of instructions that a computer reads to carry out a function. E..G. You tell the computer to print a document. The computer will read the instructions (algorithm) and perform the printing function. 

To understand the quantum-based algorithm, it is essential to understand how contemporary/conventional computing systems work. 

Whether it’s a handheld gadget or a supercomputer working in the server room of Google, every current computing device employs the binary language, where every bit of information can exist in either one of two states: 0 or 1 (hence ‘binary’), but not both states at once. 

When we discuss quantum algorithms, they follow the idea that any particle-wave system can exist in multiple states at any given time.

This means when data is stored in a quantum system, it can be stored in more than two states. This makes quantum bits (also referred to as ‘qubits’) more powerful than the conventional method of binary computing.

Standard Binary Computing Vs. Quantum Computing 

Seamless pattern with abstract binary code, digital matrix background
4 rows of 8 bits = 4 rows of bytes. Photo: iStock

The fact that a quantum bit can exist in multiple states gives quantum computing an edge over conventional binary computing. With the help of a simple example, we will try to demonstrate how quantum theory is superior to its classical counterpart. 

Picture a cylindrical rod, and each end of the rod is a bit, labeled 1 or 0. When one side is a 1, then the other side must be a 0. 

On the other hand, the quantum bit exists in every possible state simultaneously, between the 1 and 0 together. 

The above explanation exhibits that quantum bits can hold an unprecedented amount of information and hence the computing governed by this type of algorithm can exceed the processing of any classical computing machine. 

A quantum computer can compute every instance between
0 and 1 simultaneously, called parallel computing.  

Quantum Entanglement

Apart from storing more information than classical computers, quantum computing can also implement the principle of entanglement. In simple words, this principle will enable every quantum bit to be processed separately.

Beneficial Uses of Quantum Computing

The processing capabilities of quantum computing make it an ideal machine to carry out many tasks where conventional computers fall short.

Science and Life Sciences 

The study of complex atomic and molecular structures and reactions is no easy task. A lot of computing capacity is required to simulate such processes.

For instance, the complete simulation of a molecule as simple as hydrogen is not possible with the available conventional computing technology. So, quantum computing can play a significant role in understanding many of the concealed facts of nature and more particularly, of life. Many chemicals and physical and biological research work previously stalled for years can take off after quantum computers become a reality. 

Artificial Intelligence and Machine Learning



Even though scientists have made significant inroads in the area of machine learning and AI with the existing computing resources, quantum computing can help take the giant leap to make a machine as intelligent as human cognition.

Machine learning feeds on big data, which is the processing of humongous databases; in other words, big data contains a colossal amount of information, above and beyond what conventional databases contain. And the more information you have, the more intelligent you become! 

With the fast processing of quantum computing, even conventional AI will become obsolete, revamping it into a new and more powerful artificial intelligence.

Improvement of General Optimization Procedures 

With the addition of big data, the processing that takes place involves more than just reading information. It also involves the ability to make more decisions.

It is called if/then conditions, meaning if something exists and something else acts on it, what could be the outcome? The conditions use variables to calculate each condition.

So, the more data, the more variables to calculate. Putting it another way, the number of permutations and combinations increases, and thus, the amount of processing power increases. When this happens, the amount of data to be processed can increase exponentially.

Some examples would be the optimization of a financial plan might need the processing of several petabytes, equivalent to about 500 billion pages of printed text. Implementation of such extensive computing can only be achieved with the processing power of quantum machines.

Other Side of the Coin: The Dangers Involved with Quantum Computing 

One should not be surprised by this heading. We have seen through the course of history how the advent of new technology, intended for the benefit of humankind, is followed by its misuse. 

One example is Einstein’s famous equation E = mc2, which gave scientists the idea of building an atomic bomb. Although Einstein was a man of peace and his theory was never indented to be used for destructive purposes, it became so anyway; hence, with quantum computing, this unrestrained processing power can be harnessed for nefarious purposes. 

Quantum Computing Puts Data Encryption Practices in a Great Peril 

Computer keyboard with credit cards and lock on top
Photo by Shopify Photos from Burst

And as we know every precious commodity is vulnerable to vandalism, breaches, and thefts. So, to address this vulnerability, computer scientists have developed encryption modules that are used to lock the data, and only those that have the encryption key can access it, with such a password. 

Unauthorized parties can’t get around this encryption without a technique called brute force cracking. But it is important to mention that brute force attacks might only work to crack simple passwords that consist of only a few bytes. 

Let’s try to better understand this with the help of numbers

With today’s computers, It could take more than a billion, billion years to crack data that is protected by what is called a 128-bit  encryption key, widely used by financial resources on the Internet.

A standard 128-bit key can’t get cracked by the brute force algorithm using the conventional binary coding system, but when we replace this two-state concept with a quantum bit of unlimited existing states, the tables surely get turned.

The result is that a 128-bit Key that is so formidable against the brute force of classical binary supercomputers will fall flat when quantum computing is used to carry out the brute-force algorithm.

No operating quantum machine exists today, but experts have estimated that a quantum supercomputer would be able to crack 128-bit encryption keys within 100 seconds. Compare that to the billon-billion years it would take a binary computer to crack the same code!

Aftermath 

If data encryption becomes ineffective, it will expose everything to criminal elements. To understand just a fraction of this devastation, imagine that every person on earth linked to the banking system loses access to their account. The mere idea of such a situation can send chills down your spine.

Apart from that, the neutralization of data encryption can lead to cyber warfare between nation-states. Here also, rogue elements will easily be able to capitalize on the situation.

A global outbreak of war in a world with the existing eight nuclear powers can end up with a dreadful outcome. All things considered, the manifestation of quantum computing can bring along many irretrievable repercussions. 

Preparation to Protect Against the Nefarious Use of Quantum Computing 

Google and IBM have successfully carried out quantum computing in a controlled environment. So, to think that quantum computers are a distant reality won’t be deemed an insightful judgment. For that matter, businesses should start preparing against this abuse. There is no point in waiting for formal rules and protocols to be issued. Experts working in the area of digital security and cryptography recommend some measures to protect business data in the future from any exploitation of the quantum era. 

Conclusion 

How technology has progressed in the last few decades is indicative of the fact that quantum computing is the reality of the future. So, the arrival of quantum computers is not the question of ‘if’ – it’s the question of ‘when’.

Quantum theory, with all its benefits for the development of life sciences, the financial sector, and AI poses a great threat to the existing encryption system, which is central for the protection of any type of confidential data. The proper approach for any nation and business is to accept this unwanted aspect of quantum mechanics as a technological hazard and start preparing against it with the help of experts. 

With that said, it will also be a blessing when used proactively for the benefit of humankind and we look forward to a better lifestyle for each of us when quantum computing becomes a reality.

Units of Power and How They are Related to Electricity

Before we learn about kilowatts and kilowatt-hours, let’s get a jump start (pun intended ????) on what these terms mean.

The Units of Electrical Power

Note: If you are not a physics enthusiast and want to skip the calculations, you can jump to this section.

Let’s travel into our way back machine and go back to high school physics 101. These terms and measurements are for background purposes only. We will not be using them later on, but understanding these concepts can help you better comprehend how power (energy) is referenced in units of watts (w) and how they are calculated. Let’s do it!

Speed

The rate of time at which an object is moving along a path.
Units: Length, Time
Example: The car traveled 1 mile in 60 seconds or 1 mile/minute.
Further Reading: What is speed in physics?

Velocity

The rate of time at which an object is moving along a path in a particular direction.
Units: Length, Time, Direction. More precisely, length/time (speed) in a particular direction.
Example: The car traveled 1 mile/minute going west.
Further Reading: What is the difference between speed and velocity?

Acceleration

When we speak about acceleration, it is the rate at which the velocity changes. In other words, velocity doesn’t stay constant.
Units: Feet per second per second or feet/second squared.
Example: A plane traveling south accelerates from 550 m/h (mph) to 600 m/h over a time period of 40 seconds. It has a change in velocity from 550 m/h to 600 m/h and the time period that this occurs in 40 seconds.
Further Reading: Speed, velocity, and acceleration.

Newton

Here we add a new component – Force. When we talk about the measurements of Newtons, we are talking about an acceleration (remember, acceleration means just a change in velocity) of an object.

Illustration_on_One_Newton
By Mhermsenwhite – Own work, CC BY-SA 4.0, https://commons.wikimedia.org/w/index.php?curid=70624309

One newton is the force needed to accelerate one kilogram of mass at the rate of one meter per second squared in the direction of the applied force. Simply put, this is the amount of push (force) of one kilogram of an object that weighs one kilogram at a changing velocity (acceleration) of one meter per second per second.
Units: 1 kg⋅m/s2
Example: Joe is pushing a box weighing one kg down the road at 1 m/s

Joule

Joules refer to the amount of work done. A joule is equal to the work done by a force of one newton moving one meter, so Joe has pushed the box weighing one kg down the road at 1 m/s squared for a distance of 1 meter. A joule is also referred to as energy.

Say Watt?

The number of Joules that an electrical device (e.g a lightbulb) is burning per second. Joules and watts both refer to work and equate to power, but both are interchangeable.

Here is the connection:

1 Watt = 1 Joule per second (1W = 1 J/s), so a watt is the amount of energy (in Joules) that an electrical device (such as a light) is running per second. So if a device is burning 500 watts for 60 seconds, then a Joule would equate to 500 * 60 = 30,000 J. Moving ahead, if an air conditioner is burning 1000 watts for 1 hour (60 sec * 60 min = 3600 seconds), then that equates to 1000 watts * 3600 seconds = 3,600,000 Joules (of energy that was used for that hour).

A kilowatt is equal to 1000 watts, so 1 kWh represents the amount of energy transfer that occurs over one hour from a power output of 1000 watts (i.e., joules per second). Thus 1 kWh is equal to 3,600,000 joules of energy transfer (work).

What Does This Mean?

It means that the work of one newton is being performed in the form of electrons that are being pushed through the wire per meter. Saying it in a simpler form, one watt is one joule of energy running a device per second.

  Just Tell Me in Plain English What a Watt is!

Transparent Light Bulb
Consider this to be a one-watt light bulb. If it was a two-watt light bulb, it would be about twice as bright. If it was a 500-watt bulb, more power is needed to provide that additional wattage; hence, more power or we can say more current or voltage is needed, and up goes your electric bill! See how it works? Photo by LED Supermarket

Glad you asked. 1 watt is equal to voltage times current: W=EI  (don’t worry, you don’t have to memorize this formula). Also known as power, a watt is a unit of power.  The more the voltage and/or current that flows through the wire, the more power (watts) is used to run the device.

Let’s Talk About Time

Devices run for a period of time, right? So we have to add this value to our watt calculations. That way, we will know how many watts are used for a certain period of time, and as we will see later, this will help us determine what it costs to run electrical devices, or more specifically, what the electric company charges us and why.

Examples: Joe turned on a one-watt lightbulb for 60 seconds, so that is equal to 60 watts.

Now Joe turned on a 250-watt lightbulb for 2 minutes, so that is equal to (250 * 0.333 hours) = 83.25 watts.

(Remember, for you physics guys, 83.25 watts is the same as saying that 4995 joules of power have been generated).

We’ll be going into this in another article, but just to enlighten you, if your electric company charges you 14.34 cents per 1000 watts used per hour (that’s what they generally charge in New York), then, using the example above, you have paid the company 14.34 cents * (per 1000 watts) * 0.25 watts * 0.0333 / hour (2 minutes) = .036 cents per hour.

If Joe ran the 250-watt bulb for 1 hour, then he would be paying 3.6 cents per hour, but if Joe ran a 1000-watt device for 1 hour, he would be paying 14.34 cents.

OK, but if Joe ran the 1000 watt bulb for 10 hours, then he would owe the energy company $143 cents or $1.43.

OK forget about Joe. What if your electric company charges you 14.34 cents per hour for a 2000-watt air conditioner? You would be paying 29 cents per hour, so if you run the air conditioner for 10 hours each day, you would be paying $2.90 every day. That’s $29.00 every 10 days or close to $100 per month.

Say 1000 Watts!

Are you getting tired of hearing of thousands of watts? This author is also, so let’s call 1000 watts – 1 kilowatt. There you go. Kilo means 1000 so 1kw is 1000 watts.

If you run a 1000-watt device for 1 hour, then the designation is 1Kwh (1 kilowatt-hour or you can say a 1-kilowatt device is running for one hour), denoted as kWh. So, 1 kilowatt is equal to 1,000 watts. If a unit consumes 60 watts hourly and runs for 60 hours, then the energy consumption rate will be 60 watts x 60 hours to equal 3,600 watts per hour, which is equal to 3.6 kWh of electricity.

Ok we know, you want to know what it cost to run your electrical devices in your home and you probably want to know about your air conditioner for starters.  Let’s just say that a typical air conditioner runs about 3 kWh per day. To calculate how much that costs you, just call your local energy company to get the correct number. For our area, Nassau County, the cost is 7 cents per kWh. If you want to know more about your air conditioner costs, check it out here.

 

 

Gas Cars Vs. EV Cars Costs Comparisions 2023

White Tesla Model 3 Charging at Home
Austin, Texas, 2-1-2021: Tesla Model 3 charging at home in front of a house on an L2 charger. Photo: iStock

Note: If you want to bypass the calculations below and go directly to the actual costs of charging an EV against today’s gas prices, go to our Costs of Charging an EV in this article.

2023 Update

PSEG is now providing the monthly costs for home charging. Below is an example of a real Long Island homeowner’s EV statement from PSEG.

PSEG EV Monthly Cost email
Photo: SMS ©

 

Why Electric?

There are a number of benefits of driving an electric vehicle (EV). One is the cost savings on gas. The other is the environment. We will concentrate on the former now and will talk about the environment in a separate article.

Before we start discussing how EV costs are calculated, make sure you have read our articles on the atom, electric current and Units of Power and How They are Related to Electricity so that you will be able to keep up with our cost calculations that involve knowledge about watts and kilowatts, but if you haven’t, no worries. You can skip to the bottom to get our estimate of EV electrical costs when charging from the home, or just read the review below. 

Review

Here’s a brief overview for those who didn’t read the articles mentioned above.

    • Electrons are subatomic particles (one of the entities within an atom) that travel through the wire when power is applied (the wire is attached to an electrical socket). This is known as electrical current and is referred to in units of amps. More on this here.
    • Voltage is the force that pushes the electrons through the wireSimilar to turning on the pressure of a water faucet.
    • Current usually flows through a copper wire which is the conductor and the wire is covered by an insulator (rubber packaging around the wire so that the copper is not bear).
    • Resistance is the opposition to the current (electrons) that is flowing in an electrical circuit. Think of it as the friction that brushes along the side of the current.
    • A watt is the energy (power) that runs the electric device. It is a product of how much electrical current is running and how much voltage (push) is occurring. It is determined by multiplying the voltage times the current. The formula is E=IR (E=voltage, I=current, and R=resistance).
    • A kilowatt is 1000 watts (kW).
    • A kilowatt-hour (kWh) equates to 1kw that runs a device for 1 hour.

Example: If you run an air conditioner for one hour and that air conditioner uses 70 kilowatts of electricity per hour, then you have used 70 kilowatts of electrical energy for that hour. If you run the air conditioner for two hours, you would have used up 140 kilowatts of energy.

Most EVs, with the exception of the high-end luxury ones, have batteries that consist of a 60-65kWh capacity. Sparing you the formula, a battery of this size will equate to about 260 miles after a full (100%) charge.

Note: Most EVs are set to charge to 80% only. Constant charging to 100% diminishes the battery’s lifetime. 80% of a 65kWh battery equates to about 230 miles. 

How Do Kilowatts Relate to Electrical Costs?

Electrical Towers
High voltage transmission towers with red glowing wires against blue sky – Energy concept. iStock

Conventional Gas Cars

We will use a 2021, 4-cylinder Nissan Altima as our example.
Gas tank size: 16.2 gals and MPG: 31 average. 

If we multiply 31 miles/gals * 16.2 gals, we can determine the total mileage that this car can run on a full tank of gas, which is 502 miles.  

As of this writing, the price for a gallon of gas is $5.00 on average across the United States. So $5.00 * 16.2 gallons (a full tank) equals $81 to fill up.

Electrical Vehicles

Electric Vehicle being charged in a garage
Photo by Michael Fousert on Unsplash

For EVs, we calculate units per mile instead of MPG. For this example, we will use a 2020 Kia Niro EV, which is a fully electric vehicle and contains a 65kWh battery.

As mentioned, the industry standard for charging a 65kWh EV to 80% is about 230 miles.

Note: If you have an EV, never let it go below 30%, as you may run into trouble if you are on the road and can’t find a charging station, especially in the winter time.

Let’s review what we know so far:

    • Filling up a gas tank of a 2021 Nissan Altima will take you about 502 miles without having to fill up again.
    • The cost to fill up this car as of this writing is $81.00.
    • To charge a 2020 Kia Niro’s battery to 80%, the car can go about 230 miles without having to recharge.

Local Averages Using Electric Utility Calculations

Transparent Light Bulb
Photo by LED Supermarket, Pexels

We called PSEGLI directly to find out the average cost of electrical consumption for a typical home in Nassau County. Keeping it simple, an average home uses about $.33 per kWh (this includes delivery and service charges).

According to one source, 7.2 kWh is used each hour to charge the battery and if it takes approximately 4 hours to charge, the total kWh is 28.8 kWh.

28.8 kWh x $.33 = $9.5.

Rounded off, it costs about $10.00 to charge a 65kWh battery, which equates to 230 miles, but if you’d like to be a little more cautious if you think that might be too low (since there are so many variables involved that might not meet your particular driving habits or lifestyle, we can say the approximate cost for charging a 65kWh battery from a 220/240-volt level 2 charger is $15.00. How’s that?

Proportion 

We will now compare filling a gas tank of a conventional car which equates to the same mileage (230 miles).

Here are the steps: 

    • Divide the total mileage to charge the battery to 80% by the total mileage to fill a gas tank to get the percentage between the two: 

230 mi / 502 mi = 45% 

    • Multiply this percentage by the total cost to gas up a car: 

To get the cost for a conventional car to go 230 miles, we multiply the cost to fill up the gas tank ($81.00) by 45% to match the 230 miles, and that cost would be 0.45 *$85 = $38.7. 

Using an average of today’s gas prices ($5.00 as of today), it would cost a gas car $38.7 to go 230 miles of highway driving and an EV car would cost $15 to go the same distance (230 miles) in Nassau County, New York.

Note: As of October 2022, the price of gas fell to $3.5 / gallon, so proportioning this price, we get the cost to fill a gas tank to go 230 miles is – ($3.5 x 16.2) x 0.45 = $25.5, which is about 7 gallons of gas.

That’s still a savings of $15.5 for every 230 the gas car drives.

Cost of Charging an EV

Update: As of January 2023, PSEG and other utilities are now using disaggregation. A technique that breaks down energy utilization by appliance via AI computer algorithms. Below is an example of disaggregation of a common household’s individual energy usage by appliance.

Notice that $91 was spent on EV charging for the 30 days of November 11, 2022, to December 12, 2022. That’s $22.75 per week using standard electrical charges (not Time of Use as described below).

In comparison, one SUV that averages 25 MPG and traveled 1,100 miles for that same time period would have cost $149.60 at today’s price of $3.40 per gallon. Similarly, a typical mid-sized sedan traveling 1,100 miles would run $124.66.

You can calculate your specific mileage costs here.

PSEGLI Energy Breakdown by Applicance

Selective Electric Utility Plans Overview

Most electric utility companies provide more than one plan that you can select for your household. Besides the default plan which provides the same price for electric consumption 24×7, there is a plan that can allow you to select lower rates based on different times of the day.

This plan, called Time of Use (TOU) is available at PSEGLI and NYC’s Con Edison, as well as many other utility companies nationwide. Refer to their brochure as to exactly how this works.

If you have not already done so, change your plan to TOU and schedule your EV charging for after midnight on weekdays.

You can also apply the same schedule for your dishwasher, washer and dryer and any other appliance that uses electricity.

PSEGLI TOU Chart
PSEGLI TOU Chart

Take a look at the electric bill above from PSEG of Long Island (PSEGLI) above, which powers Nassau County and where the offices of Howard Fensterman are located.

Electrical power companies charge per kWh and we did some preliminary calculations starting with the delivery charges in the bill, and that doesn’t include the actual electrical costs after that.

Note: It can take up to four hours to charge an EV using a level 2 charger.

Gas hose on a money background

 

 

 

 

 

 

PSEGLI EV home charging graph
Image capture: PSEGLI

 

Conclusion

If you are looking to save money on gas, EV cars are the way to go. Yes, these vehicles are more expensive than conventional gas cars, but at $3,50 per gallon, you will be pleasantly surprised how much your savings can accumulate.

Finally, we leave you with this. Below is a copy of the estimated charges that accrued for the month of July 2022, from a 1,100-square-foot home that has an EV in its garage in Nassau County, NY. The family charges the car to its 80% capacity about three-four times per month. Notice that the cost in the Electronics category is only 10% of the total usage in the house. Something to think about!

Copy of estimated charges from PSEGLI for a home in Nassau County
Photo: SS

 

 

What is Voltage and Electrical Current? (A Brief Guide)

Electrical Towers
High voltage transmission towers with red glowing wires against blue sky – Energy concept. IStock.

Electrical current is the measure of electrical flow. It’s measured in amperes, or amps for short. The current refers to the number of electrons that pass by a point in an electrical conductor in one second, and it’s usually given in units as milliamps (mA) or microamps (μA). This article explains what electrical current is and how it works. Keep reading to learn more about this topic!

How Does Electrical Current Work?

Electrical current travels through a wire (conductor) to reach a device (eg. light bulb) which causes the device to enable. This traveling of electrons through the wire to the device is called a circuit. It is the pathway for an electrical current to flow from the source to the load. 

Wires showing copper cables
Copper cables are surrounded by rubber insulation. The copper wire is the pathway from the source to the load.  iStock

 

 

 

 

 

 

There are three basic parts to a circuit:

    • The “source,” or “sourcing device,” is where the electrons come from. This can be a battery, a generator, or the flow of electricity from a wall outlet. 
    • The “load,” or “dumping device,” is where the electrons go after completing the circuit. This could be a light bulb, an appliance, or some other device. 
    • The “pathway,” or “wiring,” is the middle part that brings the electrons from the sourcing device to the dumping device. The wiring is almost always made of copper, iron, or in electronic devices, a semiconductor. The current can only flow when the circuit is complete. When the circuit is broken, the current stops.

What Is Electrical Conductivity?

Electrical conductivity is the ability of a material to allow an electrical current to flow through it. The term conductivity is used to describe the extent to which a material will allow the flow of an electrical current. If a material has high conductivity, such as copper, it means that it is very good for allowing electrons to flow rather freely through the wire, while low conductivity, such as rubber will inhibit the electron flow to a greater extent, known as resistance.

The harder it is for the electrons to flow, the more resistance the material has. That’s why the rubber is used to insulate the copper wire in almost all manufacturing that will transmit electric current. Rubber has a high resistance rating. 

Wood and glass are two types of materials that have very low conductivity ratings. Have you ever used wood to connect to an electrical circuit or battery? On the other end, copper is one of the most conductive materials around and that is why you see so many wires and/or cables that have copper wiring.

Besides the type of material that is used, electrical conductivity can be affected by several factors. For example, temperature, and the presence of contaminants like dust and water.

What is Voltage?

Turn on your water faucet about a quarter of the way and place a cup under it. Notice how fast (or slow) the water is running to fill the cup. How long did it take?

Now turn the faucet to make the water run faster. When you do this, the water fills up the cup sooner. 

This is your voltage (actually an equivalent of voltage). The faster the water comes out, the more the force or pressure of water will be used. In electricity, this means that the more the pressure, the faster the electric current will come out to power an electrical device. The bulb will light up quicker, which you won’t notice, since it happens so quickly, but that is what will happen.

Ohm’s Law

A law that states the relationship between voltage, current, and resistance in a conductor (or insulator). It states that voltage is equal to current times resistance or E=IR. So the voltage equates to the amount of current that flows through the wire but includes the amount of resistance the current is subjected to. 

Types of Electrical Current

There are two basic types of electrical current: Direct Current (DC) and Alternating Current (AC). A direct current is a constant flow of electrons that always flows in the same direction. It can flow in one direction or it can flow in both directions. It is provided by batteries, solar cells, and hydroelectric plants. Electrical current can be changed from DC to AC by using a device called a transformer. Transformers are used to change the voltage of the electricity.

Summary

Electrical current is the flow of electrons through a conductor. A complete circuit is where electrons flow from the source to the load through a pathway or wiring. Electrical current works when a circuit is complete. A circuit is a pathway for an electrical current to flow from the source to the load. There are 3 basic parts in a circuit. The source is where the electrons come from. The load is where the electrons go after completing the circuit. The pathway is the middle part that brings the electrons from the sourcing device to the dumping device.

There are two basic types of electrical current: Direct Current (DC) and Alternating Current (AC). A direct current is a constant flow of electrons that always flows in the same direction. AC can change from DC to AC by using a device called a transformer.

What is a Computer Bit and How Does it Work?

Man working on multi computers
Photo by CDC-Pexels

What Makes Computers Tick?

When you think of computing, you may have images of whizzing processors or geeks typing on screens. But did you ever wonder how all these devices work? If so, keep reading.

As technology continues to advance and computer literacy becomes more important than ever, we are going to break down what makes computers tick!

Electricity is the Common Demonator

Set of realistic vector hands pressing light switches
You turn on a switch and you are allowing current to flow. That is represented by a ‘1’ in a computer language called Binary Code. You press Off and cut out the electric current from flowing, which is represented by a ‘0’. Photo iStock.

You flick a switch and a light bulb turns on. You flick the switch again and the blub turns off. If I were to tell you that computers run on this simple principle, would you believe me?   Well, believe you should because that’s all there is. Simply refer to a bulb that is lit as the number ‘1’ and when it is off, refer to it as a ‘0’.

In other words, the values ‘0’ and ‘1’ are based on whether electricity, more popularly referred to as current, is flowing and is represented by ‘1’ or current is not flowing, represented by ‘0’.

So Should I Call Them Ones and Zeros?

Not exactly. These two values are known as bits. So whatever you are doing on the computer; such as reading this article, you are actually reading a long list of bits that the computer sees and then it translates those bites into words. 

Of course, it is a bit (pun intended) more detailed than that. Not complex though, just a little more to absorb. Starting with the fact that when I mentioned “reading a long list of bits”, we have to translate these “long lists” into an organized pattern that the computer can understand; in other words, how to translate them into something we humans will understand.

I’ll Byte!

Seamless pattern with abstract binary code, digital matrix background
4 rows of 8 bits = 4 rows of bytes. Photo: iStock

If you align eight bits in a row where some are set to ‘1’ and others are set to ‘0’, you have created what is referred to as a byte.

It’s an arrangement that has a particular meaning to the computer.

A byte can be any letter or number from A-Z, 0-9 respectively. It can also store special characters, For example, binary code 00001101 is equal to 13 in decimal form. The alphabetic character “M” is similar in bit arrangement, but with one bit (pun intended again) of a difference, and that is it has an extra ‘on’ bit – 01001100. 

If you were to type the letter ‘R” on your screen, it would involve a different combination of eight bits. In this case, for the letter ‘R, the sequence would be 01000010, and the letter ‘S’ would be 01000011, and so on. 

Let’s backtrack and look at how these bits equate to their electrical equivalent. For our ‘M’ example above, which has the bit arrangement of 01001100, that would equal the following combination of electrical current that is, in this exact sequence: off, on, off, off, on, on, off, off.

It is based on a table called ASCII (As Key), which displays the eight bits (bytes), in ascending sequence, where each byte equates to a letter or number.  

The particular instruction would depend upon the arrangement of the 1s and 0s. If you think this seems like some type of code, it is and is called binary code.

Bites and Bytes Review

  • A bit is a switch that is either electronically on or off.
  • A byte is a combination of eight bits.
  • Each pattern of bits in the bytes represents a number, letter or special character.

Understanding how computers use bits and bytes can help you understand how they process everything from the simplest math problems to streaming video or playing games online. Keep reading to learn more about this topic!

Why are Bits Important?

Bytes determine whether a file is an image, document, spreadsheet, movie, audio file or other medium and they tell your computer what to do with the information in that file.

Converting information into digital form is called encoding; the process of converting it back into its original state is called decoding. Encoding and decoding both involve assigning values to different pieces of information so that a computer can store and process it appropriately.

For example, let’s say you have a picture that you want to save on your computer. The picture will be broken down into individual pixels and assigned an identifying number. This number will represent the color of each pixel (e.g., red, blue, or green). Thus, encoding this picture involves assigning numbers to each piece of information in it—in this case, the colors of each pixel in the photo.

Decoding would work the same way it would give a pixel its original identifying number so that it could once again be identified as a specific color; thus allowing you to see the photo as intended by its creator!

Bits in Programming

When you’re programming a computer, you use bytes to represent information. For example, when the programmer asks the computer to calculate 5+5, it translates this into binary. “0001 0010 0101” So in binary, 5+5 is “0110 0100 0101” (This is called a binary addition). These two numbers are added together and the answer of 10 is sent back. And that’s how bits work!

Writing the Computer Program

PHP computer instruction
Photo by KOBU Agency on Unsplash

Computer programs read what’s called instructions. It tells the computer to do things, as explained in the following examples.

      1. Print Something
        When you tell your computer to print a document, there are instructions that tell it to do just that.
        Scan the document or picture.
        Contact the printer.
        Send the document or picture to the printer.
        Tell the printer to print it.
      2. An ATM Example
        In banking, a set of computer instructions tells the system to read a customer’s checking balance when he/she is at an ATM. If the individual attempts to withdraw funds that are more than what’s in the checking balance, the person would be told there is not enough money in the account for this withdrawal.
      3. Here are computer program instructions written in Python that determines if a variable input of a stock price is higher than 50 and display a corresponding message:
        # Get the stock price from the user
        stock_price = float(input(“Enter the stock price: “))# Check if the stock price is higher than 50
        if stock_price > 50:
        print(“Your stock is growing!”)
        else:
        print(“Your stock is not growing.”)

        In this example, the program prompts the user to enter the stock price, which is stored in the variable stock_price.

        The program then uses an if statement to check if the stock price is higher than 50. If it is, it displays the message “Your stock is growing!” using the print function. If the stock price is not higher than 50, it displays the message “Your stock is not growing.”

This is called an if/then condition and is extremely common in computer programming. Also called a logical statement.

The same situation will occur over and over and the same result will happen. There is no determination that there may be more issues occurring, such as possible fraudulent activity and that is where artificial intelligence comes in as we discuss in our AI 101 article.

Summing Up

A computer bit is the smallest unit of information that a computer can read. When you align eight bits in a row, it is called a byte and each byte represents a letter, number, or special character, which is defined by the arrangement of the bits in the byte.

The translation of each byte can be found in the ASCII table. Bits are used to process everything from the simplest math problems to streaming video or playing games online.

What are Semiconductors and How Do They Work?

Close up photo of a motherboard
Semiconductor Computer Chips. Photo by CristianIS https://pixabay.com/users/CristianIS-2094012/ on Pixabay

Overview

This is where we describe the device that controls the flow of electricity inside the semiconductor so that the bit patterns (bytes) can become the language that the computer will translate into human literacy, or in layman’s terms, translate from bytes to English characters, numbers, and special characters.

Driving the Current

You might say electricity hates semiconductors because current can only travel through them when you tell it to, or more specifically when you turn a switch on or off. It is similar to driving a car. You can’t drive down the road and not think there will be any obstacles such as a red light to stop you.

A good example is to picture your car as the current and the road as the semiconductor. Now imagine a light bulb at the end of the road. If the current (your car) continues to travel down the road without hitting a stop light, you will reach the bulb, and voila! You (the current) reached the bulb and lit it up.

Car on road with arrow pointing to light bulb
Photo by SS. Light bulb Pixaby.

But what if there was a red light on the road? You must stop the car (stop the flow of current) and then there is no voila. The bulb will not light because no electricity was allowed to continue down the road to reach it.  

Another analogy is when you turn on a faucet to allow water to flow. When you are done, you turn it off and the water stops flowing, but you can also control the speed or force at which the water comes out. It is this force that can be equated to voltage when referring to electricity. Let’s look at this in a bit more detail. 

The Voltage Factor

So the flow of electricity that is controlled through the semiconductor is via the amount of voltage that is being used. If too little voltage is implemented, then no electrical current will flow through, but if you raise the voltage, it will trigger the semiconductor to open the gate and allow the current to flow through. In other words, voltage is the controlling factor in whether current will or will not flow through the conductor.

The Managing Device Within the Semiconductor

This control of whether current flows or doesn’t flow through a semiconductor has a name – transistor, which is nothing more than a switch to allow or disallow electricity to travel through it. The transistor will open when a specific amount of voltage (force) is used but will close when not enough voltage is used.

Before semiconductors were introduced, transistors were controlled by vacuum tubes. They were large, bulky devices, but they worked the same way as today’s tiny transistors do. You may recall seeing old photos of large rooms filled with vacuum tubes. That’s what it took to just make some simple calculations.Transistor size comparisons

Transistor Sizes as Compared Throughout the Decades. Top-Left is a vacuum tube that would represent one transistor., equating to one state of either on or off. The rightmost device is a semiconductor computer chip that can contain hundreds or even thousands of transistors with simultaneous on and off states. Photo vlabo from iStock

Today’s transistors are tiny and the hundreds, if not thousands of vacuum tubes that filled a room can now fit on a computer chip the size of your fingernail. These ‘chips’, sit on a board, called a motherboard that connects the circuits which allow the current to run along with it.

Computer Board
Photo by Miguel Á. Padriñán: https://www.pexels.com/photo/green-circuit-board-343457/

The transistor’s on and off states create logic that represents the basic building blocks of the decision making process; however, we don’t refer to this process as on or off. Instead, we represent it by numbers. ‘1’ represents ‘on’ and ‘0’ represents ‘off’, which in computer talk are called bits.

Our article on how bits and bytes work explains this in more detail. 

What are Semiconductors Made Of?

Transistors are made of silicon and germanium, an element typically found in sand. The physical characteristics of silicon and germanium can be perfect conductors to allow current to flow without much resistance, but can also be perfect insulators to stop any current from flowing, which makes it a truly superior mineral when you need to control electricity.

Summary

Transistors allow current to flow or not to flow through it. The material that the current resides in is silicon, which is used because its properties allow it to work well as a conductor but just as well as an insulator. Each on or off state is represented by a ‘1’ or ‘0’ and is called a bit. Eight bits make a byte, and it is the particular pattern of bits in each of the bytes that determines a certain instruction for the computer to follow.

What Would Space Aliens Really Look Like?

Space Alein. AI Generated
Photo: Fotor

The Extraterrestrial Delima

Some say that we are the only intelligent life in the universe, but others tend to differ, and if you include the calculations in our article Life in Outer Space, a Mathematical Approach, there is a good probability that they are correct.

But we are probably the only planet that has species that look exactly like us. The aliens would have to live under the same environmental conditions that exist on this planet. If there is just a .001% difference on their planet as there is on Earth, our alien friends could look much different.

That’s because all living things on Earth have physically adapted to this planet’s environment; such as adapting to the atmosphere, which is 78 percent nitrogen and 21 percent oxygen, as well as adjusting to the planet’s range of temperatures and seasons. The result is that we are a species that consists of two ears, two eyes, two lungs, and a bunch of other organs that keep us alive through these earthly conditions.

So the chances are very high that there isn’t a planet exactly like Earth, but some exoplanets in the habitable zone might come pretty close. Instead of saying we may be the only intelligent life in outer space, it may be more prudent to say we may be the only intelligent life that looks like us in outer space.

An Exoplanet With a Slight Change

Illustration of an alien planet
Photo iStock

Suppose that there is a planet revolving around a star 100 light-years from Earth.  We’ll call this planet Exo, but on this planet, there is a slight change in its atmosphere, namely, its oxygen level is 90 percent nitrogen and 10 percent oxygen.

On Earth, it is 78 percent nitrogen and 21 percent oxygen. So if aliens from Exo would happen to land on Earth, their lungs would need to be 11% larger than ours, in order to compensate for the lower oxygen level that their bodies are naturally accustomed to on their planet.

Now suppose that Exo is 20% further from its star than the Earth is from our sun (Earth is 93,000,000 miles away). That would mean that it would be 18.6 million miles further away from its star as compared to Earth’s proximity to our sun. Everything would be darker on Exo and cooler as well.

Our hypothetical species would require larger eyes than us to compensate for the lack of sunlight. Needless to say, their winters will be colder, so those living in a Siberian type of weather on Exo would have thicker skin than their counterparts on the warmer side of the planet (warmer relative to that planet’s environment, not ours).

Artists creation of extratresials
iStock

In this case, we would be looking at beings with larger chests, bulging eyes, and thick skin as compared to us. So they would need some type of protective gear or suits in order to compensate for the increased oxygen and lighter atmosphere. If they don’t have this protection, they would be consuming too much oxygen and risk having severe eye conditions, possibly even going blind if they are outside too long.

So when you see sci-fi movies that show extraterrestrial beings walking on our planet without some sort of protection, it would not be an accurate portrayal.

What About Gravity on Exo?

The amount of gravity would be determined by the size (mass) of the planet, so if Exo is 10% larger than Earth, then the creatures living there would probably have heavier and stronger legs. Their legs may bulge out more or they may be longer than what we humans would look like, or maybe they have three or four legs. Not a far thought since thousands of species on this planet also have four legs.

For a more in-depth look at how aliens may evolve, take a look at this video below.

Time is Everything

We have discussed how the physical characteristics of alien life might look on a habitable planet similar to life here on Earth. But what about their evolution process? Did it take the same amount of time for these aliens to evolve as we did? In other words, humanoid life on Earth has been estimated period and 200 million years ago, but does that mean that creatures on other planets began their evolution process within the same time period as we did?

What Year Is It?

We first have to consider that a year on Exo would probably be different than our years. If Exo is 10% further away from its sun, then it will take longer for the planet to revolve around it, a 365-day revolution (if days are the same there) won’t work. We estimate that it takes 400 Exo days for it to complete one of its years.

Are We the Most Intelligent of All Species in the Universe? Watch What You Say!

The above scenario is based upon a similar period it would take for beings like us to evolve on a different planet. Chances are that this would not be the case.

What if Exo was formed 500 thousand years later than it did on Earth? Well, that would mean that they would have evolved only to what we could equate to Neanderthals. Now that type of communication doesn’t look promising.

But what hat if Exo was formed 500 thousand years earlier than here on Earth?  That would mean that Exo’s inhabitants would have hundreds of thousands of years more time to evolve than we humans have on this planet.

If their evolution started that much earlier then we could conclude that they are mentally superior to us. If that is the case and they do (or some believe that they have already) come to Earth, will they be friendly?

We Come in Peace, Maybe.

Scientists are contemplating a new communication with ET via signals to be sent from huge telescopes here on Earth. It will be called the Beacon in the Galaxy and will contain mathematical,  physical, and biological representations of earthlings, as well as our location in the Milky Way galaxy. But if aliens do find this and they equate to the scenario of advancement over us, is this a smart move? Only time will tell!

Here’s Why Your Car Overheats

Before we begin, we need to note that if you have an electric vehicle (EV), this information will not apply, since EVs don’t have radiators and subsequently, cannot overheat, but if you do have a conventional gas car, the information supplied below can be very helpful so that you don’t get stuck with a radiator that overheats.

Overview

Woman looking at an overheated car
Photo: iStock

When it comes to nightmares for conventional car owners, engine overheating is probably on your list. If you want to avoid regular car repairs, proper maintenance is necessary, including keeping your vehicle’s radiator in tip-top shape.

However, before you do that, you need to understand why your car’s radiator can overheat. There are many different causes of engine overheating.

The following are the most common causes.

Your Car’s Radiator

Gas engines can get very hot. This is because energy is discharged as the spark plugs ignite causing the pistons to make their repetitive up-and-down motion.

To keep the heat energy from getting out of control, the engine block is constantly being cooled via engine coolant that circulates the engine. The coolant liquid that resides in the radiator helps reduce the heat within the enginean so that it doesn’t overheat.

The radiator is one of the key components of the cooling system that is responsible for keeping your engine cool. It is an enclosed vented chamber containing channels for the fluid (normally water) that transfers heat from one location to another more efficiently than if there were no intermediary medium at all.

Radiators are most commonly used in automobiles with internal combustion engines, but they are also found in other applications such as air conditioning systems, industrial process cooling, and heating systems in homes.

Car Radiator
Car Radiator. Photo: iStock

Low Coolant 

But what if there is no coolant available?

Low or no coolant in the radiator is the leading cause of engine overheating; therefore, it is vitality important that you regularly check your coolant and fill it up if it’s low. Moreover, this is especially important in the summer. 

Poorly Working Electric Fan

Apart from a low coolant level, another thing that often causes engine overheating is a defective electric fan. At times, your fan will burn and will stop working. Therefore, you must regularly check whether the fan motor of your car is working.

Broken Fan Belt

Your car will overheat if its fan belt is broken. Usually, a fan belt is found in older cars, and fixing it is easy. Also, by looking at the engine, you can easily tell whether or not you have a broken fan belt.

Leaky Water Pump

Look beneath the car when you stop it in case your vehicle continues to overheat regardless of what you do. You may have a water leak from the pump if you witness a significant amount of liquid beneath your car.

Check the coolant level in the radiator. If it is low on more than one occasion, it is most likely that you have a leaky water pump. To test this out, make sure your radiator is filled with coolant, and then take the car for a short drive. If your coolant keeps going low then you most likely have a water pump that is not functioning properly. If this is the case go to your repair shop as soon as possible and get it fixed. 

Blocked Radiator

If your car has over 50,000 miles, then there’s a good chance that the radiator is filled with gunk, preventing it from running properly. Solving this problem is easy. All you have to do is flush your radiator. If you flush your car’s radiator once a year, you will prevent it from getting blocked. Best to have your mechanic do this for you.

Thermostat That Does Not Open

At low speeds, thermostats do not need to come into play. However, once you push the accelerator, the thermostat must open to allow more coolant to flow through. If that does not happen then your car is likely to get overheated.

There you have it—why your car overheats. Regardless of what causes it, you must get an overheated engine fixed as soon as possible. 

Going to your local car repair shop is your best bet for doing it right.

 

Howard Fensterman Minerals